Scopus Publications
- Computational study of carbon nanotube (CNT)-based nanofluid performance in hollow fiber membrane contactor for H2S separation
Zahra Sayyah Alborzi, Fateme Ghasemi, Younes Amini, Hadise Sayyah Alborzi, Hamid Reza Moazami, N. Madhwesh
International Journal of Modern Physics C, 2026
In this study, the removal of H2S was investigated using hollow fiber membrane contactors (HFMCs). The absorbent fluid was a nanofluid containing carbon nanotubes, which was added to the absorbent fluid to enhance H2S absorption. After the modeling and model validation of the HFMC, the nanofluid effect on the H2S separation performance was discussed. A 2D HFMC model was considered, and COMSOL software was used for the model’s numerical solution. In the following, gas and nanofluid concentration distribution, velocity development profile in the membrane tube side, pressure drop in the tube side, the effect of gas flow rate on H2S removal, the effect of hollow fiber number and the effect of liquid flow rate on H2S removal were investigated. The results showed that adding the nanofluid to the absorbent fluid led to a significant increase in H2S absorption in all cases. Additionally, the results indicated that increasing the gas flow rate and decreasing the absorbent fluid flow rate could result in a decrease in H2S removal. The investigation of pressure variations in the absorption process from 1 to 10 bar also showed a slight increase in H2S removal (approximately 5%). Furthermore, the conversion of the conventional fluid to the nanofluid resulted in an approximately 40% increase in H2S removal. - Application of halloysite nanotubes (HNTs) in membrane technology for oil separation; A review study
Younes Amini, Mohammad Amin Sedghamiz, Amin Hassanvand
Materials Today Communications, 2026 - Comparative experimental evaluation of wood charcoal and cocopeat fillers in a pyramid-shaped solar still for enhanced desalination performance
Arunkumar H. S, Avinash K. Hegde, K.Vasudeva Karanth, Younes Amini, Madhwesh N
International Journal of Thermofluids, 2025
Freshwater scarcity remains a persistent challenge in arid and coastal regions, necessitating cost-effective and energy-efficient desalination solutions. This study presents an experimental performance evaluation of a pyramid-shaped solar still (PSS) enhanced with porous fillers cocopeat and wood charcoal to improve distillate productivity. The PSS, fabricated with a black-coated stainless-steel basin and insulated with thermocol and foam, was operated using both tap and saline water under coastal climatic conditions. Incorporation of fillers significantly improved the thermal regime and overall yield compared to the base model. The charcoal–saline water configuration exhibited the best performance, achieving a daily distillate yield of 950 mL and a thermal efficiency of 23.17%, representing a 34% enhancement over the base saline-water case (17.3%). Cocopeat improved heat retention but resulted in slower evaporation and lower yield. The enhanced absorptivity of charcoal promoted higher basin water temperature and better energy utilization. All configurations produced very soft distillate (10–20 mg/L as CaCO₃), meeting WHO potable water standards. The findings demonstrate that low-cost filler materials, particularly wood charcoal, can significantly augment the thermal and distillation efficiency of PSS, highlighting their suitability for decentralized desalination in resource-constrained regions. - Impurity-induced gamma radiolytic production of hydrogen, deuterium, and oxygen in nuclear reactors
Valiyollah Ghazanfari, Armin Taheri, Younes Amini, Fatemeh Mansourzadeh, Mohammad Mahdi Shadman
Nuclear Engineering and Design, 2025 - CFD Simulation of Various Two-Phase Flow Patterns in Y-Shaped Microfluidic Channels
Younes Amini, Valiyollah Ghazanfari, Amir Hossein Saeedi Dehaghani, Mohammad Mahdi Shadman, Fatemeh Mansourzadeh
Journal of Chemical and Petroleum Engineering, 2024
This study presents a computational fluid dynamics (CFD) simulation of two-phase flow patterns in a Y-shaped microfluidic device. The two-phase flow of water and n-butyl acetate is simulated using the volume of fluid (VOF) method in a Y-shaped microfluidic device with different flow rates. A 2D model was used for simulation, and the results were compared to experimental data, showing good consistency. The study also examined the effects of organic (n-butyl acetate) and flow on the overall flow model. The authors observe three different flow patterns, including slug flow, parallel flow, and droplet flow, depending on the flow rate. The results indicate that a slug flow pattern is detected when the flow rates of the aqueous and organic phases are both low and similar. Nonetheless, as the overall flow rate rises, the slug flow pattern shifts to either parallel droplet or plug flow. Similarly, when the flow rate of the aqueous phase is increased while keeping the organic phase flow rate constant, the shift occurs from slug flow to droplet flow. Therefore, this study is significant in providing insights into the different flow regimes that can occur in a microfluidic system. This understanding can be used to design and optimize microfluidic devices for a variety of applications. - Effect of Chamfered Turbulators on Performance of Solar Air Heater - Numerical Study
Arunkumar H S, Madhwesh N, Anirudh Hegde K, Manjunath Mallashetty Shivamallaiah, Kota Vasudeva Karanth, Younes Amini
Cfd Letters, 2024
This paper presents a numerical analysis of the thermal performance improvement in a flat plate solar air heater equipped with chamfered turbulators attached below the absorber plate for evaluating performance for Reynolds numbers ranging from 3,000 to 21,000. According to the research, chamfered turbulators caused the flow to become highly turbulent. This flow behaviour with flow separation around the turbulators positively affects performance. This paper attempts to explain the complex flow behaviour found during the analysis. The turbulator diameter varies in 1 mm increments from 3 to 7 mm at a constant longitudinal pitch of 200 mm. The number of turbulator rows in the transverse direction is kept constant at three. The chamfer is represented by the flow attack angle, which can be 30°, 45°, or 60° facing the direction of flow and opposing the direction of flow. The results showed that a 7mm diameter turbulator with a 30° chamfer angle placed against the flow of air yielded a considerably more significant thermal enhancement factor of 1.15 over the spectrum of flow Reynolds number studied - Optimized Q-cascade approach for stable cadmium isotope purification using Newton-Raphson and direct substitution methods
Radiation Physics and Engineering, 2024 - Numerical investigation of thermal-hydraulic performance enhancement in helical coil heat exchangers with twisted tube geometries
Valiyollah Ghazanfari, Mohammad Mahdi Shadman, Fatemeh Mansourzade, Younes Amini
Case Studies in Thermal Engineering, 2024
This numerical study examines the thermal-hydraulic performance of helical coil heat exchangers (HCHEs) using twisted tubes versus conventional circular tubes. The effects of Reynolds number (Re = 10,000 to 100,000), pitch length (11, 7.2, 5.5, 3.6 mm), and twisted tube orientation (co-current, counter-current) on heat transfer efficiency and pressure drop were investigated. The results show that higher Reynolds numbers can reduce the Resistance factor by approximately 25 % and improve heat transfer by approximately 35 %. An optimal pitch length of 5.5 mm was found to balance enhanced heat transfer and manageable pumping costs. Twisted tubes demonstrate significant performance advantages at lower Re, with 20–33 % higher Performance Evaluation Criterion (PEC) values compared to circular tubes. However, the benefit diminishes at higher Re, with less than 10 % PEC increase. Implementing counter-current twisted tube configurations leads to approximately 13 % higher Nusselt number and 11 % higher Resistance factor, resulting in a 10 % overall PEC improvement. These findings highlight the superior thermal-hydraulic performance of twisted tubes in HCHE applications, especially at lower Reynolds numbers. Future work could explore different fluids, advanced optimization, energy analysis, cost assessment, and additional geometric parameters to further enhance twisted tube heat exchanger design and performance. - A comprehensive study on the kinetics and isotherms of D2/H2 adsorptive separation using pure and composite Cu-BDC-NH2 MOFs at 77 K
Abolfazl Dastbaz, Javad Karimi-Sabet, Younes Amini, Mohammad Ali Moosavian
International Journal of Hydrogen Energy, 2024 - Enhancing heat transfer in a heat exchanger: CFD study of twisted tube and nanofluid (Al2O3, Cu, CuO, and TiO2) effects
Valiyollah Ghazanfari, Armin Taheri, Younes Amini, Fatemeh Mansourzade
Case Studies in Thermal Engineering, 2024
This study investigates the influence of nanofluids on heat exchanger efficiency using 3-D computational fluid dynamics (CFD). The objective is to optimize the performance of twisted tubes by analyzing various pitch lengths (P = 180, 135, 90, 67.5, and 45 mm). The method's accuracy is validated by comparing experimental and numerical data from previous studies. The analysis focuses on key parameters such as heat transfer factors, outlet temperatures, and pressure drops, encompassing a wide range of flow rates (0.5 kg/s to 2 kg/s). The findings demonstrate that using nanofluids in twisted tubes significantly enhances heat transfer while slightly increasing pressure drop. Specifically, when compared to the smooth tube device with six baffles, employing 0.1 vol% Cu and 0.15 vol% Al2O3 nanoparticles in the twisted tube with a pitch length of 45 mm leads to heat transfer improvements of 1.04 and 1.12 times, respectively. Moreover, eliminating baffles favoring the optimized twisted tube configuration results in a notable reduction in pressure drop by approximately 1.55 times. These results highlight the potential of nanofluid implementation in enhancing heat exchanger efficiency and offer valuable insights for designing and optimizing heat transfer systems in various industrial applications. - Ce(ΙΙΙ) and La(ΙΙΙ) ions adsorption through Amberlite XAD-7 resin impregnated via CYANEX-272 extractant
Azadeh Yarahmadi, Mohammad Hassan Khani, Masoud Nasiri Zarandi, Younes amini
Scientific Reports, 2023 - Intensification of strontium (II) ion biosorption on Sargassum sp via response surface methodology
F. Soleymani, M. H. Khani, H. Pahlevanzadeh, Younes Amini
Scientific Reports, 2023 - Investigation of kinetic, isotherm and adsorption efficacy of thorium by orange peel immobilized on calcium alginate
Ali A. Gh. Khamseh, Sohrab Ali Ghorbanian, Younes Amini, Mohammad Mahdi Shadman
Scientific Reports, 2023 - Ce(III) and La(III) ions adsorption using Amberlite XAD-7 resin impregnated with DEHPA extractant: response surface methodology, isotherm and kinetic study
Azadeh Yarahmadi, Mohammad Hassan Khani, Masoud Nasiri Zarandi, Younes amini, Ali Yadollahi
Scientific Reports, 2023 - Computational fluid dynamics simulation of two-phase flow patterns in a serpentine microfluidic device
Younes Amini, Valiyollah Ghazanfari, Mehran Heydari, Mohammad Mahdi Shadman, A. Gh. Khamseh, Mohammad Hassan Khani, Amin Hassanvand
Scientific Reports, 2023 - Optimal time separation modeling and simulation for stable neon isotopes in a transient square cascade: a comprehensive study
Mohammad Mahdi Shadman, Valiyollah Ghazanfari, Younes Amini, Fatemeh Mansourzadeh, A. Gh. Khamseh, Mohammad Hassan Khani, Amin Hassanvand, Mehran Heydari
SN Applied Sciences, 2023 - Enhancement of immiscible fluid mixing using passive micromixers to increase the performance of liquid–liquid extraction
Younes Amini, Mohammad Mahdi Shadman, Valiyollah Ghazanfari, Amin Hassanvand
International Journal of Modern Physics C, 2023 - Modeling and simulation of the radiolytic deuterium and oxygen generation in heavy water reactors
Mohammad Mahdi Shadman, Valiyollah Ghazanfari, Younes Amini, Fatemeh Mansourzadeh, Armin Taheri
Nuclear Engineering and Design, 2023 - Computational Fluid Dynamics Simulation of a Membrane Contactor for CO2 Separation: Two Types of Membrane Evaluation
Zahra Sayyah Alborzi, Younes Amini, Parya Amirabedi, Saba Raveshiyan, Amin Hassanvand
Chemical Engineering and Technology, 2023 - The efficacy of magnetic force on thermal performance of ferrofluid in a screw tube
M. Barzegar Gerdroodbary, M. Jafaryar, M. Sheikholeslami, Y. Amini
Case Studies in Thermal Engineering, 2023 - A critical review with emphasis on the rheological behavior and properties of polymer solutions and their role in membrane formation, morphology, and performance
Seyedeh Mohaddeseh Mousavi, Saba Raveshiyan, Younes Amini, Ali Zadhoush
Advances in Colloid and Interface Science, 2023 - Intensification of thorium biosorption onto protonated orange peel using the response surface methodology
Ali A. Ghorbanpour Khamseh, Younes Amini, Mohammad Mahdi Shademan, Valiyollah Ghazanfari
Chemical Product and Process Modeling, 2023 - Configuration optimization of a renewable hybrid system including biogas generator, photovoltaic panel and wind turbine: Particle swarm optimization and genetic algorithms
Ali Heydari, Zahra Sayyah Alborzi, Younes Amini, Amin Hassanvand
International Journal of Modern Physics C, 2023 - Appling the computational fluid dynamics studies of the thermogravitational column for N2-CO2and He-Ar gas mixtures separation
Hesam Salimi, Neda Hashemipour, Javad Karimi-Sabet, Younes Amini
Chemical Product and Process Modeling, 2023 - Applications of Nanotechnology in the Harvesting of Solar Energy
Seyede Mohaddese Mousavi, Zahra Sayah Alborzi, Saba Raveshiyan, Younes Amini
Nanotechnology Applications for Solar Energy Systems, 2023 - Numerical study on the thermal performance of the shell and tube heat exchanger using twisted tubes and Al2O3 nanoparticles
Valiyollah Ghazanfari, Morteza Imani, Mohammad Mahdi Shadman, Younes Amini, Fazel Zahakifar
Progress in Nuclear Energy, 2023 - Optimization of liquid-liquid extraction of calcium with a serpentine microfluidic device
Younes Amini, Amin Hassanvand, V. Ghazanfari, Mohammad Mahdi Shadman, Mehran Heydari, Zahra Sayah Alborzi
International Communications in Heat and Mass Transfer, 2023 - CFD simulation of flow distribution in the randomly packed bed Dixon ring
Younes Amini, Mohammad Mahdi Shadman, Javad Karimi-Sabet
Separation Science and Technology Philadelphia, 2022 - Experimental study of nitrogen isotope separation by ion-exchange chromatography: effect of process factors
Mahdi Ahmadi-Motlagh, Younes Amini, Javad Karimi-Sabet
Journal of Radioanalytical and Nuclear Chemistry, 2022 - CFD Simulation of He/CH4 Separation by Hyflon AD60X Membrane
Younes Amini, Ali Ghaednian-Jahromi, Javad Karimi-Sabet, Abolfazl Dastbaz, A. Hassanvand
Chemical and Biochemical Engineering Quarterly, 2022 - Improvement of synthesized graphene structure through various solvent liquids at low temperatures by chemical vapor deposition method
Najmeh Koosha, Javad Karimi-Sabet, Mohammad Ali Moosavian, Younes Amini
Materials Science and Engineering B, 2021 - Analytical study of heat and mass transfer in axisymmetric unsteady flow by ADM
Amin Hassanvand, Mojtaba Saei Moghaddam, M. Barzegar Gerdroodbary, Younes Amini
Journal of Computational and Applied Research in Mechanical Engineering, 2021 - Microfluidic solvent extraction of calcium: Modeling and optimization of the process variables
Payman Abdollahi, Javad Karimi-Sabet, Mohammad Ali Moosavian, Younes Amini
Separation and Purification Technology, 2020 - Experimental and numerical study of mass transfer efficiency in new wire gauze with high capacity structured packing
Younes Amini, Javad Karimi-Sabet, Mohsen Nasr Esfahany, Masoud Haghshenasfard, Abolfazl Dastbaz
Separation Science and Technology Philadelphia, 2019 - Numerical study of n-heptane/benzene separation by thermal diffusion column
Neda Hashemipour, Javad Karimi-Sabet, Kazem Motahari, Saeed Mahruz Monfared, Younes Amini, Mohammad Ali Moosavian
Chinese Journal of Chemical Engineering, 2019 - Injection of multi hydrogen jets within cavity flameholder at supersonic flow
Amirhossein Edalatpour, A. Hassanvand, M. Barzegar Gerdroodbary, Rasoul Moradi, Y. Amini
International Journal of Hydrogen Energy, 2019 - Liquid-liquid extraction of calcium using ionic liquids in spiral microfluidics
Shirin Marsousi, Javad Karimi-Sabet, Mohammad Ali Moosavian, Younes Amini
Chemical Engineering Journal, 2019 - CFD simulation of the structured packings: A review
Younes Amini, Mohsen Nasr Esfahany
Separation Science and Technology Philadelphia, 2019 - Experimental and simulation investigation on separation of binary hydrocarbon mixture by thermogravitational column
Neda Hashemipour, Javad Karimi-Sabet, Kazem Motahari, Saeed Mahruz Monfared, Younes Amini, Mohammad Ali Moosavian
Journal of Molecular Liquids, 2018 - The influence of coolant jet direction on heat reduction on the nose cone with Aerodome at supersonic flow
R. Moradi, M. Mosavat, M. Barzegar Gerdroodbary, A. Abdollahi, Younes Amini
Acta Astronautica, 2018 - Shape effect of cavity flameholder on mixing zone of hydrogen jet at supersonic flow
Rasoul Moradi, A. Mahyari, M. Barzegar Gerdroodbary, A. Abdollahi, Younes Amini
International Journal of Hydrogen Energy, 2018 - Application of Knudsen thermal force for detection of inert gases
A. Hassanvand, M. Barzegar Gerdroodbary, Rasoul Moradi, Younes Amini
Results in Physics, 2018 - Ion-pair extraction-reaction of calcium using Y-shaped microfluidic junctions: An optimized separation approach
Peyman Foroozan Jahromi, Javad Karimi-Sabet, Younes Amini
Chemical Engineering Journal, 2018 - Preparation and characterization of novel modified PVDF-HFP/GO/ODS composite hollow fiber membrane for Caspian Sea water desalination
Abolfazl Dastbaz, Javad Karimi-Sabet, Hossein Ahadi, Younes Amini
Desalination, 2017 - Mixing augmentation of transverse hydrogen jet by injection of micro air jets in supersonic crossflow
A. Anazadehsayed, M. Barzegar Gerdroodbary, Y. Amini, R. Moradi
Acta Astronautica, 2017 - Experimental characterization of new wire gauze with high capacity structured packing
Younes Amini, Javad Karimi‐Sabet, Mohsen Nasr Esfahany
Canadian Journal of Chemical Engineering, 2017 - The flow feature of transverse hydrogen jet in presence of micro air jets in supersonic flow
M. Barzegar Gerdroodbary, Younes Amini, D.D. Ganji, M. Rahimi Takam
Advances in Space Research, 2017 - Characterization of New Wire Gauze High-Capacity Structured Packing with Varied Inclination Angle
Younes Amini, Javad Karimi-Sabet, Mohsen Nasr Esfahany
Chemical Engineering and Technology, 2017 - Pressure-driven liquid-liquid separation in Y-shaped microfluidic junctions
Peyman Foroozan Jahromi, Javad Karimi-Sabet, Younes Amini, Hooman Fadaei
Chemical Engineering Journal, 2017 - Experimental and numerical study of air-gap membrane distillation (AGMD): Novel AGMD module for Oxygen-18 stable isotope enrichment
Ehsan Karbasi, Javad Karimi-Sabet, Jamshid Mohammadi-Rovshandeh, Mohammad Ali Moosavian, Hossein Ahadi, Younes Amini
Chemical Engineering Journal, 2017 - Experimental and numerical study of multiphase flow in new wire gauze with high capacity structured packing
Younes Amini, Javad Karimi-Sabet, Mohsen Nasr Esfahany
Chemical Engineering and Processing Process Intensification, 2016 - Experimental investigation of nanofibrous poly(vinylidene fluoride) membranes for desalination through air gap membrane distillation process
Rasoul Moradi, Javad Karimi-Sabet, Mojtaba Shariaty-niassar, Younes Amini
Korean Journal of Chemical Engineering, 2016 - Optimal control of batch cooling crystallizers by using genetic algorithm
Younes Amini, M. Barzegar Gerdroodbary, Mahmoud Reza Pishvaie, Rasoul Moradi, S. Mahruz Monfared
Case Studies in Thermal Engineering, 2016 - Vacuum enhanced membrane distillation for trace contaminant removal of heavy metals from water by electrospun PVDF/TiO2 hybrid membranes
Rasoul Moradi, Saeed Mahruz Monfared, Younes Amini, Abolfazl Dastbaz
Korean Journal of Chemical Engineering, 2016 - Experimental and Numerical Simulation of Dry Pressure Drop in High-Capacity Structured Packings
Younes Amini, Javad Karimi‐Sabet, Mohsen Nasr Esfahany
Chemical Engineering and Technology, 2016 - Air gap membrane distillation for enrichment of H218O isotopomers in natural water using poly(vinylidene fluoride) nanofibrous membrane
Rasoul Moradi, Javad Karimi-Sabet, Mojtaba Shariaty-Niassar, Younes Amini
Chemical Engineering and Processing Process Intensification, 2016 - Numerical study of shock wave interaction on transverse jets through multiport injector arrays in supersonic crossflow
M. Barzegar Gerdroodbary, D.D. Ganji, Y. Amini
Acta Astronautica, 2015 - Shear-rate-dependent rheology effects on mass transport and surface reactions in biomicrofluidic devices
Arman Sadeghi, Younes Amini, Mohammad Hassan Saidi, Hadi Yavari
Aiche Journal, 2015 - Heat transfer of swirling impinging jets ejected from Nozzles with twisted tapes utilizing CFD technique
Younes Amini, Mojtaba Mokhtari, Masoud Haghshenasfard, M. Barzegar Gerdroodbary
Case Studies in Thermal Engineering, 2015 - Numerical modeling of surface reaction kinetics in electrokinetically actuated microfluidic devices
Arman Sadeghi, Younes Amini, Mohammad Hassan Saidi, Suman Chakraborty
Analytica Chimica Acta, 2014
RECENT SCHOLAR PUBLICATIONS
- Computational study of carbon nanotube (CNT)-based nanofluid performance in hollow fiber membrane contactor for H 2 S separation
Z Sayyah Alborzi, F Ghasemi, Y Amini, H Sayyah Alborzi, HR Moazami, ...
International Journal of Modern Physics C 37 (08), 2550128 , 2026
2026
Citations: 3 - Application of halloysite nanotubes (HNTs) in membrane technology for oil separation; a review study
Y Amini, MA Sedghamiz, A Hassanvand
Materials Today Communications, 114333 , 2025
2025
Citations: 8 - Impurity-induced gamma radiolytic production of hydrogen, deuterium, and oxygen in nuclear reactors
V Ghazanfari, A Taheri, Y Amini, F Mansourzadeh, MM Shadman
Nuclear Engineering and Design 443, 114335 , 2025
2025 - Comparative experimental evaluation of wood charcoal and cocopeat fillers in a pyramid-shaped solar still for enhanced desalination performance
AK Hegde, KV Karanth, Y Amini
International Journal of Thermofluids, 101447 , 2025
2025
Citations: 3 - Enhancing thermal efficiency in helical heat exchangers: a CFD study on twisted tube configurations
V Ghazanfari, F Mansourzade, A Taheri, Y Amini, MM Shadman
Case Studies in Thermal Engineering, 106694 , 2025
2025
Citations: 22 - مدلسازی غیرخطی ستون جداسازی ایزوتوپ کربن-13 با استفاده از تقطیر تبریدی
یونس امینی، محمد مهدی شادمان، فاطمه منصورزاده، حسن خانی
سی و یکمین کنفرانس هستهای ایران , 2025
2025 - مدلسازی تأثیر غلظتهای اولیه هیدروژن و اکسیژن آب بر رادیولیزگاما در راکتورهای هسته ای
محمد مهدی شادمان، ولی اله غضنفری، فاطمه منصورزاده، یونس امینی
سی و یکمین کنفرانس هستهای ایران , 2025
2025 - مدلسازی زنجیره نفوذ حرارتی برای جداسازی ایزوتوپهای گازهای نجیب
فاطمه منصور زاده، محمد مهدی شادمان، یونس امینی
سی و یکمین کنفرانس هستهای ایران 1404 , 2025
2025 - CFD Simulation of Various Two-Phase Flow Patterns in Y-Shaped Microfluidic Channels
Y Amini, V Ghazanfari, AH Saeedi Dehaghani, MM Shadman, ...
Journal of Chemical and Petroleum Engineering 58 (2), 229-241 , 2024
2024
Citations: 3 - Optimized Q-cascade approach for stable cadmium isotope purification using Newton-Raphson and direct substitution methods
MM Shadman, F Mansourzadeh, V Ghazanfary, Y Amini
Radiation Physics and Engineering 5 (3), 49-55 , 2024
2024 - Numerical investigation of thermal-hydraulic performance enhancement in helical coil heat exchangers with twisted tube geometries
V Ghazanfari, MM Shadman, F Mansourzade, Y Amini
Case Studies in Thermal Engineering 60, 104744 , 2024
2024
Citations: 68 - A comprehensive study on the kinetics and isotherms of D2/H2 adsorptive separation using pure and composite Cu-BDC-NH2 MOFs at 77 K
A Dastbaz, J Karimi-Sabet, Y Amini, MA Moosavian
International Journal of Hydrogen Energy 61, 893-900 , 2024
2024
Citations: 25 - Efficient Optimization of Q-Cascade for Stable Cadmium Isotopes using Newton-Raphson Algorithm and Direct Substitution Method
YA M.M. Shadman F.Mansourzadeh, V. Ghazanfary
First International Conference on Nuclear Science and Technology (ICNST) , 2024
2024 - Thermal Performance in Small Modular Reactors through Al2O3 Nanoparticles in the Primary Coolant System
SMM Ghazanfari V., F.Mansourzadeh Amini Y.
First International Conference on Nuclear Science and Technology (ICNST) , 2024
2024 - Quasi-linear model of cryogenic distillation for 13C isotope separation
MM Y. Amini F.Mansourzadeh V.Ghazanfari
First International Conference on Nuclear Science and Technology (ICNST) , 2024
2024 - Efficient Optimization of Q-Cascade for Stable Cadmium Isotopes using Newton-Raphson Algorithm and Direct Substitution Method
YA M.M. Shadman F.Mansourzadeh, V. Ghazanfary
International Conference on Nuclear Science and Technology , 2024
2024 - Thermal Performance in Small Modular Reactors through Al2O3 Nanoparticles in the Primary Coolant System
SMM Ghazanfari V., F.Mansourzadeh Amini Y.
International Conference on Nuclear Science and Technology , 2024
2024 - Quasi-linear model of cryogenic distillation for 13C isotope separation
MM Y. Amini F.Mansourzadeh V.Ghazanfari
International Conference on Nuclear Science and Technology , 2024
2024 - Effect of Chamfered Turbulators on Performance of Solar Air Heater - Numerical Study
Y Arunkumar, H. S., Madhwesh, N., Anirudh, H. K., Shivamallaiah, M. M ...
CFD Letters 16 (11), 17-36 , 2024
2024
Citations: 4 - Enhancing heat transfer in a heat exchanger: CFD study of twisted tube and nanofluid (Al2O3, Cu, CuO, and TiO2) effects
V Ghazanfari, A Taheri, Y Amini
Case Studies in Thermal Engineering 53, 103864 , 2024
2024
Citations: 146
MOST CITED SCHOLAR PUBLICATIONS
- Shape effect of cavity flameholder on mixing zone of hydrogen jet at supersonic flow
R Moradi, A Mahyari, MB Gerdroodbary, A Abdollahi, Y Amini
International Journal of Hydrogen Energy 43 (33), 16364-16372 , 2018
2018
Citations: 216 - Mixing augmentation of transverse hydrogen jet by injection of micro air jets in supersonic crossflow
A Anazadehsayed, MB Gerdroodbary, Y Amini, R Moradi
Acta astronautica 137, 403-414 , 2017
2017
Citations: 174 - Heat transfer of swirling impinging jets ejected from Nozzles with twisted tapes utilizing CFD technique
Y Amini, M Mokhtari, M Haghshenasfard, MB Gerdroodbary
Case Studies in Thermal Engineering 6, 104-115 , 2015
2015
Citations: 173 - Liquid-liquid extraction of calcium using ionic liquids in spiral microfluidics
S Marsousi, J Karimi-Sabet, MA Moosavian, Y Amini
Chemical Engineering Journal 356, 492-505 , 2019
2019
Citations: 172 - Numerical study on the thermal performance of the shell and tube heat exchanger using twisted tubes and Al2O3 nanoparticles
V Ghazanfari, M Imani, MM Shadman, Y Amini, F Zahakifar
Progress in nuclear energy 155, 104526 , 2023
2023
Citations: 158 - Injection of multi hydrogen jets within cavity flameholder at supersonic flow
A Edalatpour, A Hassanvand, MB Gerdroodbary, R Moradi, Y Amini
International Journal of Hydrogen Energy 44 (26), 13923-13931 , 2019
2019
Citations: 149 - Enhancing heat transfer in a heat exchanger: CFD study of twisted tube and nanofluid (Al2O3, Cu, CuO, and TiO2) effects
V Ghazanfari, A Taheri, Y Amini
Case Studies in Thermal Engineering 53, 103864 , 2024
2024
Citations: 146 - Numerical study of shock wave interaction on transverse jets through multiport injector arrays in supersonic crossflow
MB Gerdroodbary, DD Ganji, Y Amini
Acta Astronautica 115, 422-433 , 2015
2015
Citations: 140 - The flow feature of transverse hydrogen jet in presence of micro air jets in supersonic flow
MB Gerdroodbary, Y Amini, DD Ganji, MR Takami
Advances in Space Research 59 (5), 1330–1340 , 2017
2017
Citations: 132 - CFD simulation of the structured packings: A review
Y Amini, M Nasr Esfahany
Separation science and technology 54 (15), 2536-2554 , 2019
2019
Citations: 130 - The influence of coolant jet direction on heat reduction on the nose cone with Aerodome at supersonic flow
R Moradi, M Mosavat, MB Gerdroodbary, A Abdollahi, Y Amini
Acta astronautica 151, 487-493 , 2018
2018
Citations: 115 - Shear‐rate‐dependent rheology effects on mass transport and surface reactions in biomicrofluidic devices
A Sadeghi, Y Amini, MH Saidi, H Yavari
AIChE Journal 61 (6), 1912-1924 , 2015
2015
Citations: 100 - Numerical modeling of surface reaction kinetics in electrokinetically actuated microfluidic devices
A Sadeghi, Y Amini, MH Saidi, S Chakraborty
Analytica chimica acta 838, 64-75 , 2014
2014
Citations: 90 - Ion-pair extraction-reaction of calcium using Y-shaped microfluidic junctions: An optimized separation approach
PF Jahromi, J Karimi-Sabet, Y Amini
Chemical Engineering Journal 334, 2603-2615 , 2018
2018
Citations: 88 - A critical review with emphasis on the rheological behavior and properties of polymer solutions and their role in membrane formation, morphology, and performance
SM Mousavi, S Raveshiyan, Y Amini, A Zadhoush
Advances in Colloid and Interface Science 319, 102986 , 2023
2023
Citations: 80 - Preparation and characterization of novel modified PVDF-HFP/GO/ODS composite hollow fiber membrane for Caspian Sea water desalination
A Dastbaz, J Karimi-Sabet, H Ahadi, Y Amini
Desalination 424, 62-73 , 2017
2017
Citations: 80 - Vacuum enhanced membrane distillation for trace contaminant removal of heavy metals from water by electrospun PVDF/TiO2 hybrid membranes
R Moradi, SM Monfared, Y Amini, A Dastbaz
Korean Journal of Chemical Engineering 33 (7), 2160–2168 , 2016
2016
Citations: 76 - Pressure-driven liquid-liquid separation in Y-shaped microfluidic junctions
PF Jahromi, Y Amini, H Fadaei
Chemical Engineering Journal 328, 1075-1086 , 2017
2017
Citations: 75 - Experimental and numerical study of air-gap membrane distillation (AGMD): novel AGMD module for Oxygen-18 stable isotope enrichment
E Karbasi, J Karimi-Sabet, J Mohammadi-Rovshandeh, MA Moosavian, ...
Chemical Engineering Journal 322, 667-678 , 2017
2017
Citations: 73 - Optimal control of batch cooling crystallizers by using genetic algorithm
Y Amini, MB Gerdroodbary, MR Pishvaie, R Moradi, SM Monfared
Case Studies in Thermal Engineering 8, 300-310 , 2016
2016
Citations: 70
