Jakub Měsíček

@vsb.cz

Faculty of Mechanical Engineering, Department of Machining, Assembly and Engineering Metrology
VSB - Technical University of Ostrava

Jakub Měsíček


               Download Compact PDF  
https://researchid.co/jakubmesicek

EDUCATION

2017–2021 VŠB – TU Ostrava, Faculty of Mechanical Engineering, Doctoral studies in Engineering Technology – Ph.D.

2015-2017 VŠB – TU Ostrava, Faculty of Mechanical Engineering, Master's degree in Transport Engineering and Technology – Road Transport – Ing.

2011-2014 VŠB – TU Ostrava, Faculty of Mechanical Engineering, Bachelor's degree in Construction Machinery and Equipment– Bc.

2007-2011 SOŠ a SOU strojírenské a stavební, Jeseník, secondary education, graduation studies

RESEARCH INTERESTS

realization of experiments with specialization on 3D printing of composites, preparation of samples, measurement, and study of materials for 3D printing samples, evaluation of information on the printing process, and evaluation of their impact on the mechanical and surface properties.
71

Scopus Publications

1805

Scholar Citations

16

Scholar h-index

26

Scholar i10-index

Scopus Publications

RECENT SCHOLAR PUBLICATIONS

  • Preliminary evaluation of the spatial variability of 3D scanned corroded surface of a steel coupons
    M Krejsa, P Konecny, J Mesicek
    AIP Conference Proceedings 3489 (1), 140009 , 2026
    2026
  • Prediction of ratcheting and LCF damage using a memory surface in cyclically hardening additively manufactured AlSi10Mg with enhanced uniaxial ratcheting resistance
    R Halama, W Macek, B Tomiczek, Z Poruba, F Sari, J Rahimi, J Mesicek, ...
    International Journal of Fatigue, 109658 , 2026
    2026
  • Metal-doping induced catalytic suitability of CoWO4@ 3D-printed electrode for nitrate reduction coupled glycerol oxidation
    K Sharma, R Langer, DDA Buelvas, J Hajnys, J Mesicek, M Otyepka, ...
    Applied Catalysis B: Environment and Energy, 126602 , 2026
    2026
  • Enhancing surface quality of M300 maraging steel components produced via selective laser melting: a comparison of tumbling techniques
    A Mechali, J Hlinka, M Sajgalik, J Hajnys, J Zelinka, J Mesicek, ...
    Progress in Additive Manufacturing, 1-22 , 2026
    2026
  • A review on support-free printing with powder bed fusion method
    J Hajnys, QP Ma, R Vandzura, M Gelatko, J Mesicek, J Petru, M Pagac
    Progress in Additive Manufacturing 11 (1), 717-733 , 2026
    2026
    Citations: 3
  • Continuous Filament Fabrication Technology and Its Mechanical Properties for Thin-Walled Component
    T Kozior, J Bochnia, J Hajnys, J Mesicek
    Materials 19 (1), 144 , 2025
    2025
    Citations: 1
  • Development of in-house PC/ABS blends and optimization of printing parameters for material extrusion method
    HT Nguyen, QP Ma, J Prochazka, Z Studeny, D Dobrocky, J Mesicek, ...
    Materials & Design, 115290 , 2025
    2025
    Citations: 4
  • Machine Learning application in predicting the properties of Ti-6Al-4V samples produced with Power Bed Fusion technology
    QP Ma, HS Nguyen, DQ Vo, J Hajnys, J Mesicek, M Pagac, J Petru
    Results in Engineering, 107404 , 2025
    2025
    Citations: 4
  • Effect of part orientation and thickness on radiation shielding in FDM 3D printing of PET-G composite with tungsten
    J Mesicek, P Alexa, E Posmykova, QP Ma, A Musil, J Hajnys, E Olsovska, ...
    Journal of Materials Research and Technology , 2025
    2025
    Citations: 2
  • Investigating the impact of post-processing techniques on surface morphology and wettability of Inconel 718 components fabricated via selective laser melting
    P Gautam, A Nag, J Hajnyš, J Měsíček, J Petrů
    Engineering Science and Technology, an International Journal 68, 102105 , 2025
    2025
    Citations: 6
  • Lightweight design of mountaineering protection gear: Procedure, Optimization, and Testing
    M Sotola, P Marsalek, D Rybansky, M Fusek, J Mesicek, J Hajnys
    Engineering Science and Technology, an International Journal 68, 102086 , 2025
    2025
  • Effect of Surface Modification for Efficient Electroplating of 3D-Printed Components
    D Klichová, H Krupová, J Měsíček, F Botko, S Radchenko
    Machines 13 (7), 630 , 2025
    2025
  • EFFECT OF HEAT TREATMENT ON THE MECHANICAL PROPERTIES AND MICROSTRUCTRURE OF ADDITIVE MANUFACTURED TI-6AL-4V ALLOY.
    THSON LAM, J MESICEK, D LE TRI, QPHU MA, H LE THAI, J PETRU
    MM Science Journal , 2025
    2025
  • Effect of Heat Treatment on Additively Manufactured Inconel 718
    A Mechali, J Hlinka, M Sajgalik, M Petrovic, J Mesicek, J Hajnys, ...
    International conference on From Smart City to Smart Factory for Sustainable … , 2025
    2025
  • Topology Optimization of the Effector Arm
    E Posmykova, M Werdich, J Mesicek, J Hajnys, M Pagac, R Golebski, ...
    International conference on From Smart City to Smart Factory for Sustainable … , 2025
    2025
  • Comparative analysis of residual stress distributions in a braking pedal from a historical motorbike manufactured via selective laser melting and wire arc additive manufacturing
    L Kudrna, F Fojtík, J Kozák, P Váňová, QP Ma, J Hajnyš, R Potrok, ...
    The International Journal of Advanced Manufacturing Technology 138 (3), 1113 … , 2025
    2025
    Citations: 1
  • Research about SLM 3D printing-M300 maraging steel surface and post-processing characteristics
    A Mechali, J Hlinka, J Hajnys, T Cegan, J Zelinka, J Mesicek, M Sajgalik, ...
    The International Journal of Advanced Manufacturing Technology 138 (2), 709-724 , 2025
    2025
    Citations: 5
  • Preparation of a Ti–Al–Si based intermetallic alloy from Ti6Al4V and AlSi10Mg powders by laser powder bed fusion and hot isostatic pressing
    T Cegan, J Jurica, K Skotnicova, M Pagac, M Stamborska, L Horsak, ...
    Materials Advances 6 (23), 9133-9149 , 2025
    2025
    Citations: 1
  • Investigation of factors affecting the sound absorption behaviour of 3D printed hexagonal prism lattice polyamide structures
    M Vašina, J Měsíček, M Mánek, QP Ma, J Hajnyš, J Petrů
    Scientific Reports 14 (1), 30852 , 2024
    2024
    Citations: 8
  • Effect of powder recycling on the surface and selected technological properties of M300 maraging steel produced via the SLM method
    A Mechali, J Hlinka, M Kresta, M Petrovic, J Mesicek, I Jahan, J Hajnys, ...
    Journal of Manufacturing and Materials Processing 8 (6), 267 , 2024
    2024
    Citations: 10

MOST CITED SCHOLAR PUBLICATIONS

  • A review of vat photopolymerization technology: materials, applications, challenges, and future trends of 3D printing
    M Pagac, J Hajnys, QP Ma, L Jancar, J Jansa, P Stefek, J Mesicek
    Polymers 13 (4), 598 , 2021
    2021.0
    Citations: 1063
  • Influence of scanning strategy parameters on residual stress in the SLM process according to the bridge curvature method for AISI 316L stainless steel
    J Hajnys, M Pagáč, J Měsíček, J Petru, M Król
    Materials 13 (7), 1659 , 2020
    2020.0
    Citations: 92
  • On flexural properties of additive manufactured composites: Experimental, and numerical study
    D Krzikalla, J Měsíček, R Halama, J Hajnyš, M Pagáč, T Čegan, J Petrů
    Composites science and technology 218, 109182 , 2022
    2022.0
    Citations: 57
  • Prediction of model distortion by FEM in 3D printing via the selective laser melting of stainless steel AISI 316L
    M Pagac, J Hajnys, R Halama, T Aldabash, J Mesicek, L Jancar, J Jansa
    Applied sciences 11 (4), 1656 , 2021
    2021.0
    Citations: 56
  • Abrasive surface finishing on SLM 316L parts fabricated with recycled powder
    J Mesicek, QP Ma, J Hajnys, J Zelinka, M Pagac, J Petru, O Mizera
    Applied Sciences 11 (6), 2869 , 2021
    2021.0
    Citations: 40
  • Effect of artificial aging on the strength, hardness, and residual stress of SLM AlSi10Mg parts prepared from the recycled powder
    J Měsíček, T Čegan, QP Ma, R Halama, K Skotnicová, J Hajnyš, J Juřica, ...
    Materials Science and Engineering: A 855, 143900 , 2022
    2022.0
    Citations: 38
  • Research of 316L metallic powder for use in SLM 3D printing
    J Hajnys, M Pagac, J Mesicek, J Petru, F Spalek
    Advances in Materials Science 20 (1), 5-15 , 2020
    2020.0
    Citations: 31
  • Analysis of torsional stiffness of the frame of a formula student vehicle
    D Krzikalla, J Mesicek, J Petru, A Sliva, J Smiraus
    Applied Mechanical Engineering 7, 315 , 2019
    2019.0
    Citations: 30
  • A bibliometrics analysis of medical internet of things for modern healthcare
    HS Nguyen, HC Danh, QP Ma, J Mesicek, J Hajnys, M Pagac, J Petru
    Electronics 12 (22), 4586 , 2023
    2023.0
    Citations: 26
  • Residual stress build-up in aluminum parts fabricated with SLM technology using the bridge curvature method
    QP Ma, J Mesicek, F Fojtik, J Hajnys, P Krpec, M Pagac, J Petru
    Materials 15 (17), 6057 , 2022
    2022.0
    Citations: 25
  • TOPOLOGICAL OPTIMIZATION OF THE FORMULA STUDENT BELL CRANK.
    J Mesicek, M Pagac, J Petru, P Novák, J Hajnys, K KUTIOVA
    MM Science journal , 2019
    2019.0
    Citations: 24
  • 3d printed Hollow off-axis profiles based on carbon fiber-reinforced polymers: mechanical testing and finite element method analysis
    M Kalova, S Rusnakova, D Krzikalla, J Mesicek, R Tomasek, ...
    Polymers 13 (17), 2949 , 2021
    2021.0
    Citations: 22
  • Comprehensive view of topological optimization scooter frame design and manufacturing
    J Mesicek, L Jancar, QP Ma, J Hajnys, T Tanski, P Krpec, M Pagac
    Symmetry 13 (7), 1201 , 2021
    2021.0
    Citations: 22
  • Topology optimization of the clutch lever manufactured by additive manufacturing
    A Mikulikova, J Mesicek, J Karger, J Hajnys, QP Ma, A Sliva, J Smiraus, ...
    Materials 16 (9), 3510 , 2023
    2023.0
    Citations: 20
  • Estimating the uncertainty of measurements for various methods and 3D printed parts
    T Kozior, J Bochnia, A Bochenek, D Malara, M Nawotka, J Jansa, ...
    Applied Sciences 14 (8), 3506 , 2024
    2024.0
    Citations: 18
  • Design procedure of a topologically optimized scooter frame part
    L Jancar, M Pagac, J Mesicek, P Stefek
    Symmetry 12 (5), 755 , 2020
    2020.0
    Citations: 16
  • A review of vat photopolymerization technology: materials, applications, challenges, and future trends of 3D printing. Polymers (Basel) 202113: 598
    M Pagac, J Hajnys, QP Ma, L Jancar, J Jansa, P Stefek, J Mesicek
    Citations: 16
  • On modelling of simulation model for racing car frame torsional stiffness analysis
    D Krzikalla, A Slíva, J Měsíček, J Petrů
    Alexandria Engineering Journal 59 (6), 5123-5133 , 2020
    2020.0
    Citations: 14
  • Optimizing a quadruped robot: A comparison of two methods
    R Pastor, Z BOBOVSKY, P OSCADAL, J MESICEK, M PAGAC, E Prada, ...
    MM Science Journal 2021 (2), 4348-4355 , 2021
    2021.0
    Citations: 13
  • On Aluminum Honeycomb Impact Attenuator Designs for Formula Student Competitions
    PM Quoc, D Krzikalla, J Mesicek, J Petru, J Smiraus, A Sliva, Z Poruba
    Symmetry 12 (10), 1647 , 2020
    2020.0
    Citations: 13