Edwin A Segura Gonzalez

@itse.ac.pa

Researcher of Research and Innovation Depatrment
Instituto Técnico Superior Especializado



           

https://researchid.co/edwin.segura

EDUCATION

Phd in Science and Materials Engineering

RESEARCH INTERESTS

polymers, biodegradable, food.

3

Scopus Publications

Scopus Publications

  • Advancements in the Use of Hydrogels for Regenerative Medicine: Properties and Biomedical Applications
    Andrea Revete, Andrea Aparicio, Bruno A. Cisterna, Javier Revete, Luis Luis, Ernesto Ibarra, Edwin A. Segura González, Jay Molino, and Diego Reginensi
    Hindawi Limited
    Due to their particular water absorption capacity, hydrogels are the most widely used scaffolds in biomedical studies to regenerate damaged tissue. Hydrogels can be used in tissue engineering to design scaffolds for three-dimensional cell culture, providing a novel alternative to the traditional two-dimensional cell culture as hydrogels have a three-dimensional biomimetic structure. This material property is crucial in regenerative medicine, especially for the nervous system, since it is a highly complex and delicate structure. Hydrogels can move quickly within the human body without physically disturbing the environment and possess essential biocompatible properties, as well as the ability to form a mimetic scaffold in situ. Therefore, hydrogels are perfect candidates for biomedical applications. Hydrogels represent a potential alternative to regenerating tissue lost after removing a brain tumor and/or brain injuries. This reason presents them as an exciting alternative to highly complex human physiological problems, such as injuries to the central nervous system and neurodegenerative disease.

  • Preparation and characterization of polymer composite materials based on PLA/TiO<inf>2</inf> for antibacterial packaging
    Edwin A. Segura González, Dania Olmos, Miguel Ángel Lorente, Itziar Vélaz, and Javier González-Benito
    MDPI AG
    Polymer composite materials based on polylactic acid (PLA) filled with titanium dioxide (TiO2) nanoparticles were prepared. The aim of this work was to investigate the antibacterial action of TiO2 against a strain of E. Coli (DH5α) to obtain information on their potential uses in food and agro-alimentary industry. PLA/TiO2 systems were prepared by a two-step process: Solvent casting followed by a hot-pressing step. Characterization was done as a function of particle size (21 nm and &lt; 100 nm) and particle content (0%, 1%, 5%, 10%, and 20%, wt %). Structural characterization carried out by X-ray diffraction (XRD) and Fourier Transformed Infrared spectroscopy (FTIR) did not reveal significant changes in polymer structure due to the presence of TiO2 nanoparticles. Thermal characterization indicated that thermal transitions, measured by differential scanning calorimetry (DSC), did not vary, irrespective of size or content, whereas thermogravimetric analysis (TGA) revealed a slight increase in the temperature of degradation with particle content. Bacterial growth and biofilm formation on the surface of the composites against DH5α Escherichia Coli was studied. Results suggested that the presence of TiO2 nanoparticles decreases the amount of extracellular polymeric substance (EPS) and limits bacterial growth. The inhibition distances estimated with the Kirby-Bauer were doubled when 1% TiO2 nanoparticles were introduced in PLA, though no significant differences were obtained for higher contents in TiO2 NPs.

  • Effect of kaolin nanofiller and processing conditions on the structure, morphology, and biofilm development of polylactic acid
    Edwin A. Segura González, Dania Olmos, Gustavo González-Gaitano, Belén Orgaz, and Javier González-Benito
    Wiley
    The effect of high energy ball milling, HEBM, and the presence of kaolin on the structure, morphology, and biofilm development of polylactic acid, PLA, were studied. Biofilm development was evaluated in terms of structural and/or morphological variations so as the sole presence of kaolin. Composites based on PLA filled with kaolin were prepared by HEBM followed by hot pressing to obtain films. Structure was studied by X-ray diffraction and Fourier transformed infrared spectroscopy whereas morphology was inspected by scanning electron microscopy and atomic force microscopy. To study biofilm development on the surface of these materials, Pseudomonas fluorescens B52 were used. The shear forces from the milling process favor kaolin dispersion within the PLA. Longer milling times and cryogenic conditions improve clay dispersion. Subsequent hot pressing process enhances the most ordered structure of PLA (α-phase) which is also favored with previous milling at longer times and under cryogenic conditions. Changes in P. fluorescens biofilm development are mainly due to modifications of surface properties induced by structural variations, being the most ordered structures those which better support bacterial adhesion and proliferation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42676.